• If the mini-cycle is unsuccessful, uL will flash until the door lid is opened, allowing the customer to view and redistribute the load. Just recently our Maytag washing machine has been failing to spin out the last rinse water at the end of a load cycle. If the door lock is defective, the washer may stop mid cycle. We have to run the spin cycle again by itself to dump the rinse water. uL is displayed when the machine/motor control detects an off-balance load, and is steady on while the washer runs a mini-cycle to rebalance the load.

Thanks, Kev Lock mechanism is working, drains on drain command but won’t spin. the pump drains the water but it will not spin t … read more When our washer started producing super wet clothes, it turned out it was a baby sock that was plugging the drain. +((!+[]+(!![])+!![]+!![]+!![]+!![]+!![]+!![]+[])+(+!![])+(!+[]+(!![])+!![]+!![]+!![]+!![]+!![])+(!+[]+(!![])+!![]+!![]+!![])+(!+[]-(!![]))+(!+[]+(!![])+!![]+!![])+(!+[]+(!![])-[])+(!+[]+(!![])+!![]+!![])+(!+[]+(!![])+!![]))/+((!+[]+(!![])+!![]+[])+(!+[]-(!![]))+(!+[]+(!![])+!![]+!![])+(!+[]+(!![])+!![]+!![]+!![]+!![])+(!+[]+(!![])+!![]+!![]+!![]+!![])+(!+[]-(!![]))+(!+[]+(!![])+!![]+!![]+!![]+!![]+!![])+(!+[]+(!![])+!![]+!![])+(!+[]+(!![])+!![]+!![]+!![]+!![]+!![]+!![]+!! Most commonly for this model is a failed rotor position sensor or a cracked stator on the motor. A belt is found around the drive motor and pulley, causing the tub to spin. is stars to spin then stops again and tries this process over.

). However, if a washer is overloaded or has been used for many years, the pulley can get bent, damaged, or worn out.

My Maytag washer model SAV5710AWW refills the tub after the wash cycle is complete. Terms —

A washer series by Maytag with a low rate of customer satisfaction and a high rate of failure. Washer stops, lid lock light flashes, and most of the time in order to get it to work again I have to unplug the machine, plug it back in, then switch it over to drain and spin cycle. If the door lock is damaged or does not latch properly, replace it. Just recently our Maytag washing machine has been failing to spin out the last rinse water at the end of a load cycle. A drive pulley is used in the washer to make the tub spin. Options. The door lock can fail either mechanically or electrically. Check for excessive soap suds accumulating in the washing machine. Rep: 25. Any help would be appreciated. Posted: 05/08/2018. 180 Questions View all . In operation since 1998, BladeForums.com has led the industry since Day 1. Maytag Bravos washer will not continue to the next cycle after the wash cycle. 1 . Make sure that the motor bolt is tight. Then after the complete cycle is done it fills again and sits there full of water. These washers have the model numbers MVWB300xxx or MVWX300xxx. It will allow us to see what you see. To determine if the door lock has failed electrically, consult your washer’s diagram and use a multimeter to test each of the door lock switches for continuity. © 2020 iFixit — Licensed under Creative Commons — Privacy — Fire hazard? Check the suspension kit of the drum to make sure that it is not excessively loose. It fills, agitates, drains, spins, rinses & spins again. [])). Permalink; History; Subscribe; Unsubscribe; Stops at spin cycle with UL. These washers have the model numbers MVWB300xxx or MVWX300xxx. Other detergents can cause excessive soap suds, which could cause the washing machine to operate at a slower spin speed than selected, resulting in sopping wet clothes.

Get shopping advice from experts, friends and the community! To check that, you will have to check the bottom on your washer. Maytag recommends you use only high-efficiency detergent in Maytag washers. Small items (like baby socks) can get up and over the rim of the barrel. Your browser will redirect to your requested content shortly. Solution: If the washer starts and seems to progress through the cycle well but doesn't move to the spin cycle, the problem may be with the locking lid switch. The following images show how to get to those two parts. Use this guide Adding images to an existing question for that. When this happens, the washer starts making a loud and strained noise when the spin cycle is on. Smelled like something burning and sparked inside stainless tub. My Maytag Bravos stops working during the spin cycle. I have a Maytag model MVWC555DW1. Step 5 Add more clothing items to the washing load. Is trying but doesn’t spin. Accessibility.

A washer series by Maytag with a low rate of customer satisfaction and a high rate of failure. You do want to consider posting some images with your question. @oldturkey03, @benlogali9 the UL code is for Unbalanced Load. • Display clears if mini-cycle successfully rebalanced the load. Everything else seems to work fine. 1 . This process is automatic. Please enable Cookies and reload the page.

Concerned about possible repair due to spark. when spin cycle is activated you get a whirling sound. Inspect the door lock for damage. its spins in one direction for couple seconds then stops n starts to spin in opposite direction...it does this back n forth over and over but never goes into spin cycle, oldturkey03

what do i need to fix if it stops on spin cycle with UL. (You must log in or sign up to reply here. Clothes still are not completely spun out. Trista @benlogali9.

Discussion in 'Gadgets & Gear' started by Strabs, May 26, 2008. Water would still drain, but not fast enough for the spin cycle. There are a few things that can cause this. what do i need to fix if it stops on spin cycle with UL. Mother has compact Maytag stackable front loader that stops when time for spin cycle.