They are made using ABS filament, and these are non-weight bearing. The Distel Hitch is a very responsive friction knot popular with arborists. Many knots are not suitable for the risks involved in climbing.

Lives may be at risk – possibly your own. Either way, the knot should be dressed to ensure that the two ends are similar in length. Although any safe end-loop would be acceptable, each loop is usually a Poacher’s Knot, a loop secured with a Double Overhand Knot around the lanyard. Join eyes in front and clip together with a carabiner. I just wanted to try things out. The Rope Slider from Shizll of The Netherlands lifts your knot without extra weight and friction at your system. Scroll to see Animated Distel Hitch Knot below the illustration and tying instructions. Distel or V.T. It tends not to jam or slip when set and dressed correctly.

The Figure 8 Knot provides a quick and convenient stopper knot to prevent a line sliding out of sight, e.g., up inside the mast. The Distel Hitch is designed for tension in only one direction, which makes it especially suitable for use in climbing, e.g., by arborists. Uses: The Distel Hitch is a slide and grip knot used to ascend a climbing rope.

However, writers also describe the Distel Hitch using three turns at the top – a “3 over 1” arrangement.

Figure Aider (3D Printed Prusik/Distel Tenders) Figure Aider’s are 3D printed tenders that allow you to move the friction hitches on your tether and linemans rope, while only using one hand. Considerable attention and effort have been made to ensure that these descriptions are accurate. Like other knots supporting critical loads, close inspection is appropriate to ensure that the hitch is tied correctly.

The Square Knot (Reef Knot) is usually learned when we tie our shoelaces. These are made by @Aksisu11 from SaddleHunter.com – also from Michigan! I tried 8mm and 10mm prussic cord for the hitch on some 7/16ths StaSet, because I don't have a climbing rope yet.

Below is a pic showing my system in use with the Blakes on the secondary TIP above and the primary TIP with the Distel, hitch tender, etc. It should be deeply distrusted when used by itself.

Knot illustrations contained in this web site are not intended for rock climbing instruction. All Rights Reserved. Similar Knots: The other slide and grip knots intended for load in only one direction include: Advantages: Amongst these various slide and grip knots, the Distel Hitch is a recommended knot for the arborist: it is reasonably easy to tie; the length of the lanyard is not too critical; it provides a nice ride; and both ends take the load.

It has many uses such as to fasten a mooring line to a ring or a post. Use a lanyard with an eye at each end. Although any safe end-loop would be acceptable, each loop is usually a Poacher’s Knot, a loop secured with a Double Overhand Knot around the lanyard.. If using a line without eyes you can tie a Double Fisherman's at each end to attach to a carabiner. No responsibility is accepted for incidents arising from the use of this content.

order to achieve the same strength. It tends not to jam or slip when set and dressed correctly. Dismiss, Be the first to review “Figure Aider (3D Printed Prusik/Distel Tenders)”, Straight Figure Aider is for use with a standard prusik, Distel Figure Aider is for use with a Distel or Schwabisch hitch.

Experience and materials used will govern the choice.

Tying it: The animation shows the Distel Hitch being tied from below. Disclaimer: Any activity involving rope can be dangerous and may even be life threatening! The Distel itself is based on a Clove Hitch but the “top” part of the hitch includes additional turns that form the spiral of rope responsible for gripping the main rope.

Better to know a knot and not need it, than need a knot and not know it.

Load can be safely applied: from the loop to either end of the rope; between the two ends with the loop hanging free; or to the loop with the load spread between the two ends. Attach the carabiner. hanging below. The Bowline Knot makes a reasonably secure loop in the end of a piece of rope. It is tied using a lanyard with a loop in each end. It's simple, "bullet proof" and I don't have to carry any extra gear topside. Problems ans questions on Distel I'm very new to climbing in general, and just tried a Distel for the first time this past weekend. The Rope Slider does what a micro pulley should do: lifting your knot when you The Clove Hitch can be used for a temporary hold, e.g., stage scenery or mooring buoy. After fourth wrap bring wrapping tail down and make an additional wrap at bottom of other wraps in same direction while tying a half hitch by tucking tail under itself in the front of the knot. © 1996 – Present, Grog LLC. There are two different design’s available based on the friction hitch you are using. The experienced user will often start at the top. They are made using ABS filament, and these are non-weight bearing. The pattern of braid(s) below decides how the friction is …

Wrap the longer end around the climbing rope to make two Half Hitches. The Distel will only grip in one direction. ow to tie the Distel Hitch Knot.

The Alpine Butterfly Loop provides a secure loop in the middle of a piece of rope. To really benefit from Hitch Climber, use a hitch with low ‘base friction’ such as the braided hitches e.g. The Distel will only grip in one direction. I'm having some problems and questions. For more information and other great products, see Genesis 3D Printing. Uses: The Distel Hitch is a slide and grip knot used to ascend a climbing rope. It is important to descend slowly to avoid friction damage to the distel cord! Please see video below explaining how these work. When I double crotch I use my rope on … The Double Fisherman's or Grapevine Bend consists of two strangle knots (like double overhand knots) each tied round the other standing end. Found in: Climbing, Hitches, Search & Rescue, Slide & Grip. It can be used on main climbing line or on a work positioning strop. However, many critical factors cannot be controlled, including: the choice of materials; the age, size, and condition of ropes; and the accuracy with which these descriptions have been followed. Make four wraps around main static rope with a hand tied or sewn prusik or spliced eye split tail friction cord. Balance the lengths and pull tight.

ow to tie the Distel Hitch Knot.

It does have two giant faults: it slips and can also bind. The coils at the top of those hitches are where the friction is concentrated. No responsibility is accepted for incidents arising from the use of this material. All Rights Reserved Copyright & Privacy (v10.0). I tried several different hitch cords with a Distel and a Blakes and for me, 1/2" Tenex (actually 3/8" buried full length inside itself) tied with a Blakes Hitch on 12mm Velocity or Poison Ivy is the ticket. Video describing how these work from @Aksisu11: Due to current delays with USPS and increased fees, we have switched to UPS for 1 pound and over packages. The Distel Hitch is a very responsive friction knot popular with arborists.

Set Speed using 1 – 5.

However, for safety, try the “4 over 1” first. Figure Aider’s are 3D printed tenders that allow you to move the friction hitches on your tether and linemans rope, while only using one hand.

DISCLAIMER: Any activity that involves ropes is potentially hazardous.

Variations: The animation shows a “4 over 1” Distel Hitch – with four complete wraps in the top section.